ORDER SAMPLES/LITERATURE USG: usg.com or
[email protected] CGC: contact Sales Representative TECHNICAL SERVICES 800 USG.4YOU (874-4968) TECHNICAL INFORMATION usg.com/ensemble usg.ecomedes.com SC3238/rev. 8-24 © 2024 USG Corporation and/or its affiliates. All rights reserved. Printed in USA Notice The information in this document is subject to change without notice. CGC Inc. or USG Corp. assumes no responsibility for any errors that may inadvertently appear in this document. CUSTOM COLOR USG ENSEMBLE™ ACOUSTICAL DRYWALL—DIRECT MOUNT WALL SYSTEM SYSTEM DETAILS USG Ensemble™ can be direct mounted to a wall or a vertical surface and used as an acoustical treatment on interior partitions above 7 feet. It can be attached to a new or existing wood or steel stud drywall partition or masonry wall to reduce reverberation. See USG Ensemble™ Design Guide for installation details. Vertical Direct Mount - Stud Partition Vertical Direct Mount - Masonry Partition Wood or Steel Stud 5/8” USG Sheetrock® Brand Panel 1" Z Furring (by others) USG Ensemble™ Spray-Applied Finish 1" USG Ensemble™ High-NRC Backer Panel Insulation Impaling Clip (by others) Perforated USG Sheetrock® Brand Ensemble™ Four-Sided Taper™ Panel Masonry Wall 1" Z Furring (by others) USG Ensemble™ Spray-Applied Finish 1" USG Ensemble™ High-NRC Backer Panel Insulation Impaling Clip (by others) Perforated USG Sheetrock® Brand Ensemble™ Four-Sided Taper™ Panel PERFORMANCE DATA Base Panel Furring Backer Panel NRC LR Fire performance USG Sheetrock® Brand Ensemble™ Four-Sided TaperTM Panels 1" Z 1" USG Ensemble™ High-NRC 0.80 .87 Class A Ensemble™ Direct Mount shall be properly fastened to framing, and considerations shall be given to the load-carrying capacity of the framing system. SYSTEM COMPONENTS Products Item Number Sizes Packaging Quantity Notes 1" 20 ga. Z-Furring5 (by others) — — — — 24" o.c. framing Insulation Impaling Clip5 (by others, AST Acoustics or equal) — — — — One clip for each backer panel 5/8" USG Sheetrock® Brand Ensemble™ Four-Sided TaperTM Panels ENSPNL96, ENSPNL120 5/8" x 4' x 8', 5/8" x 4' x 10' 26-pc. unit 8'–832 sq. ft./unit 10'–1040 sq. ft./unit Gypsum panel highly engineered to perform like an acoustical ceiling panel 1" USG Ensemble™ High-NRC Backer Panels ENSHINRC 1" x 23.5" x 47.75" 4-pc. unit 31.3 sq. ft./carton Acoustical base mat for High-NRC/High-CAC USG Sheetrock® Brand Paper Joint Tape — 250' roll 20 rolls per carton 5,000 LF/ctn Specially formulated paper tape USG Sheetrock® Brand All Purpose Joint Compound USAPJC 4.5-gal. pail Single pail 48-pail pallet 216 gal./pallet Coverage 100 sq. ft./gal. 450 sq. ft./4.5-gal. pail USG Sheetrock® Brand Plus 3® Joint Compound — 4.5-gal. pail Single pail 48-pail pallet 216 gal./pallet Coverage 106 sq. ft./gal. 480 sq. ft./4.5-gal. pail USG EnsembleTM Spray-Applied Finish, White, Custom Colors ENSSPRAF 4.5-gal. pail Single pail 48-pail pallet 216 gal./pallet Coverage 100 sq. ft./4.5-gal. pail USG ENSEMBLE™ ACOUSTICAL DRYWALL COLOR PROGRAM Custom Color Matching - Specifier to provide a color number from one of the following: • Benjamin Moore® • Sherwin-Williams® • PANTONE® Recommended Instructions: 1. Minimum order quantity for USG EnsembleTM Spray-Applied Finish is 8 pails. 2. Request customer color samples through your local USG Ensemble™ sales representative. 3. Allow three weeks to receive custom color sample. 4. Once the color sample is approved and the order is placed by the purchaser, allow three weeks for the custom-colored USG Ensemble™ Spray-Applied Finish to ship with the USG Ensemble™ Acoustical Drywall order. 5. The USG EnsembleTM Spray-Applied Finish is similar to flat finish paint in sheen. Different sheens are not offered at this time. 6. Certain very deep tone colors or certain very bright colors may not be possible to match. USG will be able to determine at the time of the custom color sample request. PHYSICAL DATA Design Guide Download SC5075 at usg.com/ensemble ASTM E1264 Classification Type XX – Gypsum, Pattern E Weight Total system weight 3.2 lb/ft2 Maintenance Download SC5048 at usg.com/ensemble Fire Classification ASTM E84 and CAN/ULC S102 surface-burning characteristics Class A Flame Spread: 25 or less Smoke developed: 50 or less Notes 1. For interior partitions only. Install above 7 feet to minimize contact or damage. 2. Not for use in areas subject to continuous high heat and/or humid conditions. 3. Install according to Section 5 Environmental Conditions listed in ASTM C840. 4. In order to ensure installed performance, component substitutions are not permitted. 5. Refer to Z-Furring and Impaling Clip manufacturer's literature. 6. For all design and system performance options, see: USG Ensemble™ Acoustical Drywall Ceiling Systems Selector Guide, SC365856. The trademarks USG, CGC, ENSEMBLE, FOUR-SIDED TAPER, PLUS 3, SHEETROCK, IT’S YOUR WORLD. BUILD IT., the USG and CGC logos, the design elements and colors, and related marks are trademarks of USG Corporation or its affiliates. Declare is a trademark of International Living Future Institute. The trademark BENJAMIN MOORE is a registered trademark of Benjamin Moore & Co. The trademark SHERWIN-WILLIAMS is a registered trademark of the The Sherwin- Williams Company. The trademark PANTONE is the property of Pantone LLC. Safety First! Follow good safety/ industrial hygiene practices during installation. Wear appropriate personal protective equipment. Read SDS and literature before specification and installation. PRODUCT CERTIFIED FOR LOW CHEMICAL EMISSIONS: UL.COM/GG UL 2818 Manufactured by USG Interiors, LLC 550 West Adams Street Chicago, IL 60661 Specialty Ceiling Systems 187
ceilings systems catalog sc2000
| Title Name |
Pages |
Delete |
Url |
| Empty |
Ai generated response may be inaccurate.
Search Text Block
Page #page_num
#doc_title
Hi $receivername|$receiveremail,
$sendername|$senderemail wrote these comments for you:
$message
$sendername|$senderemail would like for you to view the following digital edition.
Please click on the page below to be directed to the digital edition:
$thumbnail$pagenum
$link$pagenum
